Vehicles
223 not categorized PORSCHE CAYENNE BACK ORDERCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.92834102733ATK By ordering this part number you get after previous sending in your wishbone overhauled with new silent blocs back. Should it not be repairable, we will inform you immediately.
$342.10
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $2,981.74
Make a selection 93034732200 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod end consists of: 1 qty. Ball joint end 1 qty. Dust bellows / boot 1 qty. Hexagon lock nut 1 qty. Lock nut washer 1 qty. Pin high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the right and left side tie rod ends at the same time....(choose a part on the right to read more) View/Change Diagram
From $13.95
Make a selection 93050319700 This seal sits on the trailing edge of the front fender at the top just below the windshield. It is also used under the back of the rear quarter panel where it meets the side panel. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 4 necessary per car. Driver's or passengers side fitment (lhd). View/Change Diagram
From $4.92
Make a selection 93064130201GEB Remanufactured part sourced in Germany. Includes a new rubber sealing ring. Purchase a newly remanufactured unit from us and an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. Sold individually. 1 necessary per car. Please note: this is a special-order item. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis. Please call us in advance of placing your order, these are very hard to come by and in some instances, we c...(choose a part on the right to read more)
$2,014.10
Make a selection 21011199312 Improve sound and performance by decreasing exhaust backpressure with our sport catalytic kits. This kit utilizes high quality, 100 cell German tri-metallic cats and includes all the necessary gaskets and hardware for installation. Please note: an ecu upgrade will be necessary. Please ensure what type of flanges you have prior to ordering. General Fitment911 1994-98
From $2,677.39
Make a selection BES99725241S Brombacher 997 tt (TUV version) stainless steel exhaust system General Fitment911 2005-08
$4,980.80
Make a selection 96420725214 This pipe connects to the oil filter console 96420702503 and to 96420725711. It acts as a backflow line from the oil filter. We recommend replacing the heat shielding wrap, part # 96420735200 when installing this pipe. This part is sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $210.00
Make a selection 96434703200 If your outer tie rods are worn you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be very dangerous and can seriously affect steering control. Prevent that from happening by replacing them as quickly as possible with our genuine replacement inner tie rods. Once you do, you will experience tighter, more precise feedback without noise. Complete kit consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Ball joint end 1 qty. Lock nut & pin sold individually. Left or right side fitment. 2 qty. Required. Tech tip: replace the inner tie rods also for a new car steering feel ! Purchase our part # 96434705804 & 96434719...(choose a part on the right to read more) View/Change Diagram
From $55.29
Make a selection 96460601900 This switch is feeds throttle information back to the dme. It tells the system if the throttle is idling or at wide open throttle. If you are experiencing an unstable idle this may be a contributing factor. Sold individually. 1 necessary per car. View/Change Diagram
$420.00
Make a selection 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$216.29
Make a selection 99334703181 If your tie rod is worn, you will experience sloppy steering response and knocking / creaking sounds. Your tie rod keeps the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut we recommend replacing the right and left side tie rods at the same time. We also recommend replacing the bellows, part # pcg419831c sold individually. 2 necessary per car.
From $303.00
Make a selection 99660610500 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. Please note: if ordering for the 996 turbo or GT2, this is only for manual transmissions. View/Change Diagram
From $85.89
Make a selection BAT004 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,029.00
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,014.10
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection BES99102240SHD + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,293.40
Make a selection BES99110200S The headers on this latest 991 system include a double plated flange. This flange dissipates heat and vibration more efficiently and consequently does not warp like thicker single plate flanges commonly used by others. This small advancement is time consuming to make but is added in order to prevent loss of power over time and will ensure years of trouble free operation even under severe track conditions. General Fitment911 2009-12
From $7,707.70
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$585.20
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,312.00
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,303.20
Make a selection BES99602260S 200 cell catalytic “x torque” design made by m&m in Germany. General Fitment911 GT3 2003-05911 1998-05
$2,823.70
Make a selection BES99300241SK The perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. Torque is better than our other systems in the low range with the valves closed and horsepower is better with the valves open. Made for mid-range and top end performance with the added beauty of 3.5" (90mm) dual exhaust tips! + 27 crank hp & +25 crank torque (on average). - 2.9 tubing (75 mm) at the widest point. Primaries are 2.5" (64mm). - 200 cell hjs "hf" trimetallic catalytic converters. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 3.5" (90 mm) dual oval, double walled polished tips included. - dual high quality ...(choose a part on the right to read more) General Fitment911 1994-98
From $11,730.62
Make a selection BES99602160S 100 cell catalytic “x torque” design made by m&m in Germany. General Fitment911 GT3 2003-05911 1998-05
$2,818.20
Make a selection BES99709260T "brombacher" racing exhaust system for 997gt3/rs General Fitment911 GT3 2007-11
$11,661.10
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |